Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
The writer is making a number of good pointers about How to Install a Bathtub Yourself in general in the article below.
Mounting a bath tub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old bathtub is readily available, the job can move rapidly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to leave the old bathtub and also set in the new one. Make certain you have qualified on your own for the work and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to consider using one before you start. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly aid you install a brand-new bath tub in your shower room if you have already bought a new bathtub and also don't need to change the setup of your previous water supply pipelines.
Your tools and product checklist ought to consist of the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to stop strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bathtub in the needed position. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bathtub until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression join; after that do the same for the other tap.
Switch on the water as well as examine all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bathtub as well as additionally check the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bath tub needs to wait up until the bath tub has actually been utilized at the very least when as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bathroom and the tiling, causing complications with dampness and possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealer can crack fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads about Installing A Bathtub, I was thinking sharing that piece of content was worthwhile. In case you enjoyed reading our blog entry plz don't forget to pass it around. Many thanks for taking the time to read it.
Visit Website Report this page